The E03 provides high quality, yet cost-effective in-ear monitoring to on stage performers or behind the scenes personnel. The system is designed to be very easy to use and requires no installation.

The E03 consists of one wireless transmitter (E03-T) and one or more wireless bodypack receivers (E03-R) on the same channel. The transmitter features eight factory switchable channels; the receivers are single channel units that operate on one of eight channels in the 72-76 MHz band, with wide band modulation for quality audio. These frequencies are in a separate band that will not interfere with simultaneous use of VHF or UHF wireless systems on the same stage.

The E03 system has a wireless operating range of 300 feet, which allows it to be used with confidence in venues from small clubs to large theatres.

The transmitter connects to a monitor or line out from any mixing console, and broadcasts the audio as an FM signal to any number of pocket size Nady E03 receivers on the same channel. Each receiver is equipped with an adjustable volume control, and high performance earbuds. Earphone enhancers—unique clear soft plastic inserts that can help secure the earbuds — are included. The transmitter also provides a microphone input to allow wireless cueing of the performers on stage.

The E03 can provide a high quality monitor mix at significantly lower decibel levels than floor monitors. This is an important benefit for artists who wish to protect their hearing from excessive and potentially damaging sound pressure levels.

FEATURES:

• Broadcasts on 1 of 8 channels in the 72-76 MHz band, to any number of Nady E03 wireless bodypack receivers on the same channel.
• 300' wireless operating range.
• 8 factory switchable channels.
• Rear panel input for line level audio.
• Front panel input for microphone.
• Audio input gain control.
• Automatic level control.
• Extendible antenna.
• 9 volt DC input for AC-EO3 9VDC regulated power supply adapter provided.
• Power switch with red LED power on indicator.
• Audio modulation LED indicator.

SPECIFICATIONS:

• Overall System Performance:
• Frequency Response: 100 Hz - 10KHz ± 3 dB
• Signal to Noise Ratio: 60 dB
• Total Harmonic Dist.: < 0.5%
• RF Carrier Frequencies: 8 factory preset channels between 72-76 MHz.
• Channel AA: 72.1, BB: 72.3, CC: 72.5, DD: 72.7, EE: 72.9, FF: 75.5, GG: 75.7,
  HH: 75.9
• Frequency Stability: Better than .005%
• Modulation: FM ± 75 KHz
• Operating Range: Up to 300 feet line of sight
• Transmitter:
• Line Input:
• Connector: One 1/4“ phone jack
• Impedance: 100 K Ohms, unbalanced
• Mic Input:
• Connector: One 1/4“ phone jack
• Impedance: Low impedance, unbalanced, with 9 VDC at 1 mA for condenser mic
• Power Output: 80,000 μV at 3 meters
• Controls: Power On/Off, audio input gain adjust
• Indicators: Power On LED, Audio Modulation “TX” LED
• Antenna: Permanently mounted telescoping whip
• Power Requirement: 9 VDC regulated, at 200 mA, AC-EO3 adapter provided
• Dimensions: 1.25" x 8.25" x 4.25"
• Weight: 1.5 lbs
• Receiver:
• Controls: Combination volume/on-off wheel
• Audio Output: 100 mW max into 16 Ohms
• Connectors: 3.5 mm mini jack for earbuds output
• Earphones: Binaural EB-3 earbuds with optional-use EMI soft rubber inserts
• Antenna: Integral with earbud cord
• Indicators: LED power on indicator
• Sensitivity: 2 μV for 12 dB Sinad with squelch defeated. Squelches at 10 μV for min. 50 dB S-N ratio
• Mute Threshold: 8-10 μV
• Power Requirement: 9V carbon zinc or alkaline battery
• Battery Life: 17-20 hours with alkaline battery; 10-12 hours with carbon zinc battery
• Dimensions: 3.35” x 2.75” x .75”
• Weight: 2.65 oz. without battery